新闻资讯

New center

Check category
Wholesale Die casting processing products Introduce the corresponding method of bumping of zinc alloy die casting

Wholesale Die casting processing products Introduce the corresponding method of bumping of zinc alloy die casting

02 2022-08
According to the requirements of operation guidance, accumulation is not allowed, and it is necessary to place them in the workstation equipment one by one;
Wholesale Die casting processing products

Wholesale Die casting processing products

26 2022-07
Cold chamber die casting can be used when die casting metals that cannot be used in the hot chamber die casting process, including aluminum, magnesium, copper, and zinc alloys with higher aluminum content.
Ingate knowledge of Die casting processing in china

Ingate knowledge of Die casting processing in china

19 2022-07
After the molten metal enters the mold, the parting surface should not be closed immediately, and the overflow groove and the exhaust groove should not directly impact the mold core. The flow direction of the molten metal after entering the mold is as far as possible along the cast ribs and heat sinks, filling from the thick wall to the thin wall, etc.
Die casting processing in china

Die casting processing in china

12 2022-07
The entrance of the runner of the cold horizontal mold should generally be located at more than 2/3 of the inner diameter of the upper part of the pressure chamber, so as to prevent the molten metal in the pressure chamber from entering the runner prematurely under the action of gravity and starting to solidify in advance.
Advantages of Die casting processing manufacturers

Advantages of Die casting processing manufacturers

05 2022-07
The advantages of Die casting processing manufacturers include excellent dimensional accuracy of castings. Usually this depends on the casting material, typical values are 0.1mm error at the first 2.5cm size and 0.002mm error for every 1cm increase.
Optical Module china Zinc alloy die casting die

Optical Module china Zinc alloy die casting die

28 2022-06
The optical module china Zinc alloy die casting die includes a main body and a base, a mold is provided at the lower end of the pressing plate, a sliding groove is provided on the outer wall of the lower end of the sliding rod, and the sliding rod is connected with the sliding groove by clamping.
Previous page
1
2
5
Wholesale Die casting processing products Introduce the corresponding method of bumping of zinc alloy die casting
Wholesale Die casting processing products Introduce the corresponding method of bumping of zinc alloy die casting
According to the requirements of operation guidance, accumulation is not allowed, and it is necessary to place them in the workstation equipment one by one;
See more information
According to the requirements of operation guidance, accumulation is not allowed, and it is necessary to place them in the workstation equipment one by one;
Wholesale Die casting processing products
Wholesale Die casting processing products
Time of issue : 2022-07-26 14:38:46
Cold chamber die casting can be used when die casting metals that cannot be used in the hot chamber die casting process, including aluminum, magnesium, copper, and zinc alloys with higher aluminum content.
See more information
Cold chamber die casting can be used when die casting metals that cannot be used in the hot chamber die casting process, including aluminum, magnesium, copper, and zinc alloys with higher aluminum content.
Ingate knowledge of Die casting processing in china
Ingate knowledge of Die casting processing in china
Time of issue : 2022-07-19 08:26:56
After the molten metal enters the mold, the parting surface should not be closed immediately, and the overflow groove and the exhaust groove should not directly impact the mold core. The flow direction of the molten metal after entering the mold is as far as possible along the cast ribs and heat sinks, filling from the thick wall to the thin wall, etc.
See more information
After the molten metal enters the mold, the parting surface should not be closed immediately, and the overflow groove and the exhaust groove should not directly impact the mold core. The flow direction of the molten metal after entering the mold is as far as possible along the cast ribs and heat sinks, filling from the thick wall to the thin wall, etc.
Die casting processing in china
Die casting processing in china
Time of issue : 2022-07-12 08:23:16
The entrance of the runner of the cold horizontal mold should generally be located at more than 2/3 of the inner diameter of the upper part of the pressure chamber, so as to prevent the molten metal in the pressure chamber from entering the runner prematurely under the action of gravity and starting to solidify in advance.
See more information
The entrance of the runner of the cold horizontal mold should generally be located at more than 2/3 of the inner diameter of the upper part of the pressure chamber, so as to prevent the molten metal in the pressure chamber from entering the runner prematurely under the action of gravity and starting to solidify in advance.
Advantages of Die casting processing manufacturers
Advantages of Die casting processing manufacturers
Time of issue : 2022-07-05 08:37:55
The advantages of Die casting processing manufacturers include excellent dimensional accuracy of castings. Usually this depends on the casting material, typical values are 0.1mm error at the first 2.5cm size and 0.002mm error for every 1cm increase.
See more information
The advantages of Die casting processing manufacturers include excellent dimensional accuracy of castings. Usually this depends on the casting material, typical values are 0.1mm error at the first 2.5cm size and 0.002mm error for every 1cm increase.
Optical Module china Zinc alloy die casting die
Optical Module china Zinc alloy die casting die
Time of issue : 2022-06-28 08:47:29
The optical module china Zinc alloy die casting die includes a main body and a base, a mold is provided at the lower end of the pressing plate, a sliding groove is provided on the outer wall of the lower end of the sliding rod, and the sliding rod is connected with the sliding groove by clamping.
See more information
The optical module china Zinc alloy die casting die includes a main body and a base, a mold is provided at the lower end of the pressing plate, a sliding groove is provided on the outer wall of the lower end of the sliding rod, and the sliding rod is connected with the sliding groove by clamping.
Previous page
1
2
5

Foshan Nanhai Jiawei metal products Co., Ltd

Contact information:18928682636(Miss Liang)/18928682621(Mr. Tang)

Company phone:0757-85103282

Company fax:0757-85103183

Company email:sunny@nhjiawei.com / jia_tangvic@163.com

Marketing Center: No.90, hongganglihe Road, Lishui Town, Nanhai District, Foshan City

Production base: b3-1, zone 3, Enping Industrial Park, Jiangmen industrial transfer park (Enping Guangen profile Co., Ltd.)

language
中国
韩国
韩国
韩国
韩国
韩国
Copyright © 2021 Foshan Nanhai Jiawei metal products Co., Ltd 粤ICP备19125561号 Powerby :300.cn